
Chemical-free mold removal for homes and businesses
Dry Ice Blasting Mold in VALENCIA, California
Dry ice blasting mold in VALENCIA, California strips mold off wood framing, brick, and concrete without water or harsh chemicals. We use CO2 blasting mold removal VALENCIA crews trust for attics, crawl spaces, and post-flood rebuilds. If you have musty odors, black mold growth, or water damage mold, call (833) 929-5837 for a same-day look.
What's included
What Our Dry Ice Blasting Mold Service Includes
Every dry ice blasting mold job includes the full sequence from inspection to clearance testing. Here is what is covered in a standard scope, and what we quote separately if your property needs it.
Full Moisture Inspection
We inspect with a thermal imaging camera, moisture meter, and boroscope inspection camera to find every wet area, not just the visible mold. This is what keeps the blasting scope accurate and stops you from paying to treat a room that does not need it.
Containment and Negative Air
Plastic sheeting, duct tape, and a negative air machine with HEPA filters seal the work zone. Air scrubbers run for the duration so spores do not migrate into the rest of your home while we blast.
Dry Ice Blasting and HEPA Vacuum
We blast all affected hard surfaces with the dry ice blasting machine, then HEPA vacuum the debris and wipe surfaces with an antimicrobial solution. This is the core of the job and the part that removes the growth rather than just bleaching it.
Fogging and Encapsulant Coating
A fogger applies a fine antimicrobial mist into the cavity, and exposed wood gets an encapsulant coating. This step is what keeps mold from returning to the same framing after the job is done.
Clearance Testing and Report
We run a spore trap and air quality test 24 to 48 hours after treatment and give you the lab report in writing. If the count does not clear, we re-treat at no extra charge. The report is formatted for insurance and resale files.
Service overview
What Dry Ice Blasting Mold in VALENCIA, California Does
Dry ice blasting mold in VALENCIA, California is a restoration method that fires compressed dry ice pellets at 300 to 900 PSI to lift mold, soot, and grime off hard surfaces. The pellets hit at roughly -109 degrees Fahrenheit, flash-freeze the mold, and sublimate straight to gas, so there is no water, no sand, and no chemical residue left behind. We use it on wood framing, brick, concrete block, metal ductwork, and the tight corners a wire brush cannot reach.
VALENCIA sits in a dry, windy pocket of California, but that does not stop mold. Winter rain pushes moisture into attics and crawl spaces, and a slow supply-line leak behind a bathroom wall can feed black mold growth for months before you smell it. If you have been searching for dry ice mold remediation near me VALENCIA CA, we handle the inspection, the blasting, and the post-remediation mold testing so the job is documented from start to finish.
The service timeline
Our Dry Ice Blasting Mold Process
The process flexes to the condition, but these checkpoints keep decisions clear.
Inspection and Scope
We walk the property with a thermal imaging camera and a moisture meter to find the wet source, not just the visible mold. A boroscope inspection camera goes into wall cavities and under subfloor. You get a written scope the same day, usually within two hours of the call.
Containment Setup
We seal the work area with plastic sheeting and duct tape, then set a negative air machine with HEPA filters so spores cannot drift into the rest of the house. Air scrubbers run the whole time. Setup takes 45 to 90 minutes depending on how many rooms are involved.
Dry Ice Blasting
A technician in a full-face respirator and Tyvek suit runs the dry ice blasting machine at 300 to 900 PSI, working top-down so debris falls into the containment. We blast framing, sheathing, joists, and ductwork. Most single-room jobs take two to four hours; a full attic or crawl space runs four to eight.
HEPA Vacuum and Treatment
Once the blasting is done, we HEPA vacuum every surface and wipe it down with an antimicrobial solution. Then we fog the cavity with a fogger and, where the wood will stay exposed, roll on an encapsulant coating. This step takes two to three hours and is what keeps the mold from returning.
Clearance Testing
We run a spore trap and air quality test 24 to 48 hours after treatment. If the spore count is at or below the outdoor baseline, the job passes and you get the lab report. If it does not pass, we re-treat at no extra charge. You get the report in writing for your insurance file.
Tools & methods
Tools and Methods We Use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Dry Ice Blasting Machine
Fires dry ice pellets at 300 to 900 PSI to lift mold off wood, brick, and concrete. The pellets sublimate on contact, so there is no water or chemical residue left behind.
Thermal Imaging Camera
Finds temperature differences that reveal hidden moisture behind walls and under floors. It is how we locate the wet source before we blast anything.
Moisture Meter
Reads the exact moisture content in wood and drywall. We use it to set the blasting scope and to confirm the structure is dry before rebuild.
Boroscope Inspection Camera
Goes into wall cavities, ductwork, and crawl spaces through a small hole. It lets us see mold growth we would otherwise have to cut open a wall to find.
Negative Air Machine and Air Scrubber
Pulls air through HEPA filters and keeps the work zone under negative pressure. This is what stops spores from spreading into the rest of the building during blasting.
HEPA Vacuum
Captures fine debris and spores after blasting. Standard shop vacuums blow those particles back into the air, which is why we use HEPA-rated units only.
Fogger and Dehumidifier
The fogger applies antimicrobial mist into cavities after blasting. The dehumidifier pulls residual moisture out of the structure so mold does not return.
Use cases
When to Call for Dry Ice Blasting Mold
These examples show how the service framework adapts rather than forcing every call through one repair.

Crawl Space Joists in Poblats Marítims
A crawl space under a 1960s home had visible mold on the floor joists and a musty smell rising into the living room. The moisture source was a disconnected downspout dumping water against the foundation. → We reconnected the downspout, blasted the joists and subfloor, treated the wood, and installed an encapsulant coating. The odor cleared within 48 hours and the clearance test passed. The homeowner avoided replacing the joists.
Restaurant Back Wall After Drain Backup
A commercial kitchen in Camins al Grau had mold across 200 square feet of the back wall and framing after a walk-in cooler drain clogged and overflowed overnight. The owner could not afford to close for a week. → We set containment after close of business, blasted the wall and framing overnight, treated it, and ran a dehumidifier. The kitchen passed clearance and reopened the next morning with no lost service days.
Problems we solve
Mold Problems We Solve With Dry Ice Blasting
These are the calls we get most often from VALENCIA homeowners and property managers. Each one has a specific fix, and dry ice blasting is usually the fastest way to get there.
Black mold growth on attic decking after a roof leak
We contain the attic, blast the decking and rafters at 300 to 900 PSI, HEPA vacuum, and fog the space. Most attics are blasted and treated in a single day, and the clearance test confirms the spore count is back to baseline.
Musty odors from crawl space mold you cannot see
We crawl the space with a boroscope, find the moisture source, blast the joists and subfloor, then treat and encapsulate. The odor clears once the source is gone, not just masked.
Water damage mold after a supply line or appliance leak
We dry the cavity first, blast any framing that already grew mold, and treat before rebuild. We tell you which repairs need to happen before the drywall goes back so the fix holds.
HVAC mold contamination spreading through the house
We inspect the air handler and ductwork, blast the metal components, HEPA vacuum the system, and treat it. In most cases the ducts can be cleaned rather than replaced, which saves thousands.
Pricing process
Dry Ice Blasting Mold Pricing
$1,800 - $6,500 depending on scope
Square footage affected
Price scales with the area we blast. A 100 square foot bathroom is a different job than a 1,200 square foot attic. We measure during the inspection so the quote reflects the real scope, not a guess.
Access and containment difficulty
Crawl spaces and sealed attics take longer to contain and require confined space precautions. That adds labor hours. A room with a door and a window is faster to seal and cheaper to work in.
Material being blasted
Wood framing and brick blast quickly. Porous materials like insulation or rotted sheathing cannot be blasted and have to be removed and replaced, which adds disposal and material cost.
How much does dry ice blasting mold cost in VALENCIA California?
Most residential dry ice blasting mold jobs in VALENCIA run $1,800 to $6,500, with a typical single-room attic or bathroom landing around $2,400. Crawl space jobs run higher because of access and containment. Commercial work is quoted per square foot. You get a written price before we start, and the clearance test is included.
What is dry ice mold remediation in VALENCIA CA?
Dry ice mold remediation uses compressed CO2 pellets to freeze and lift mold off hard surfaces without water or chemicals. The pellets sublimate on contact, so there is no rinse step and no secondary moisture damage. We follow it with HEPA vacuuming, antimicrobial treatment, and an encapsulant coating on exposed wood.
Is dry ice blasting safe for mold removal in VALENCIA?
Yes. Dry ice blasting is safe for wood, brick, concrete, and metal, and it does not use chemicals that leave residue. The one safety rule is ventilation: CO2 displaces oxygen in a sealed room, so we run air scrubbers and monitor the space. Occupants stay out of the containment during blasting and can return once clearance testing passes.
Is dry ice blasting covered by insurance in VALENCIA CA?
Most homeowner policies cover mold remediation when the mold traces back to a covered water loss, like a burst pipe or appliance failure. We document the moisture source, photograph the affected areas, and provide the lab clearance report your adjuster needs. We can bill the carrier directly on approved claims.
Ready when you are
Get Dry Ice Blasting Mold in VALENCIA, California Today
We answer the phone, we show up when we say we will, and we quote the job in writing before we start. Call (833) 929-5837 for a same-day inspection and a straight answer on what your mold job actually needs.

Talk with the local team
Request Dry Ice Blasting Mold
Call us at (833) 929-5837 or email info@moldremediationservicevalencia.com. We answer calls 24/7 for emergencies and schedule free inspections within 24 hours. Our office is in Valencia, California, and we serve all neighborhoods.



